Lightweight, low cost girderclamp.

A lightweight low cost girderclamp with low headroom anchor point makes this a highly recommendable unit for most industrial applications.

 

Clamps Incorporating Lifting Eye and Adjusting Bar.

These girder clamps are designed for light industrial applications; particularly where a permanent overhead anchor point is required. These high strength inexpensive lightweight clamps are excellent for application in small garages and hobbyist workshops.

As with all our superclamp products each PFC unit is proof loaded and supplied with a certificate of test and inspection.

Incorporating Adjusting Mechanism and Lifting Shackle. These girder clamps are truly versatile in application and may be used for lifting, pulling, or as an anchor point. Designed specifically to provide maximum jaw grip adjustment. These products are engineered for practical use where mobility is essential. The clamps are speedily applied and do not require additional tools or width adjusting components, such as spacing washers. The left and right-hand threaded adjusting bar ensures a secure grip on the beam flange.

Incorporating Machined Jaw, Adjusting Mechanism and Lifting Shackle.

Swivel jaw adjustable girder clamps incorporate the additional benefit of horizontal jaw adjustment. This enables the full length and a maximum width of the swivel jaw to anchor evenly on a considerable surface area of the beam flange. The ‘Swivel Jaw’ range of our SuperClamp products are designed to ensure ease of application.

Incorporating Adjusting Mechanism and Lifting Shackle.

Girderdogs incorporate all the reputedly excellent and reliable design features for which our products are known. The design is enhanced by a well balanced distribution of side plates, ensuring maximum grip and hold over an adequate length of girder or beam flange. They are safe in use, and once in position, are speedily applied to a steel beam.

No additional width adjusting tools or components are required.

Incorporating V-Block Clamping Jaw.

This clamp serves as an anchor or lifting point when attached to an overhead steel angle section approved for lifting applications. The V-Block clamping jaw ensures that the clamp is securely fixed to the angle section when adequately tightened. These clamps are designed for safety and versatility - each model being suitable to accommodate a wide range of steel angle sections.
No tools required as the adjusting mechanism is an integral part of the design features, and incorporates an adjusting bar with handle.

Incorporating Height Adjustment Mechanism.

Monorail construction clamps incorporating a height adjusting mechanism are speedily applied to existing steel girders, so as to expedite the erection of a conveying system. They are provided with the facility to adjust the conveying girder in height where required. Their width and height adjusting capabilities make these versatile units an inexpensive, safe, and time saving proposition for the construction of a reliable permanent or temporary overhead conveying system.

Incorporating Stationary Height Stabilizer Block. These monorail construction clamps are designed to enable speedy erection of permanent or temporary overhead conveying systems, where existing steel girders are of an adequately balanced horizontal level. Both clamps are fully adjustable by operating the left and right hand threaded adjusting bars incorporated into the unit. The designed-in stationary height stabilizer block ensure a rigid construction of the unit. Additional tools or width adjusting components are not required to apply the unit onto existing steel girders.

For side load applications where conventional clamps are unsuitable. This universal clamp has been designed not only for vertical use, but also for side load applications, where conventional clamps are not suitable. This clamp is truly versatile in application and can be used for lifting, pulling or as an anchor point. It can be loaded at any angle and eliminates the use of spreader beams in various lifting operations. With a low headroom anchor point, it can be used as a single or twin point lifting, giving positive grip and quick application combined with lightweight construction.

Incorporating Adjustable Mechanism, For use in limited space above the beam.

This unique clamp is fitted to the top beam flanges and was designed primarily to help reduce the risk of accidents when positioning heavy load bearing equipment to the lower flange. This clamp has lifting points each side and can be used independently or together for a balanced lift. Being of light weight construction can be fitted quickly.

Incorporating Adjustable Mechanism 114mm to 204mm.

This unique top mounted beam clamp is fitted to the top beam flanges and was designed primarily to help reduce the risk of accidents when positioning heavy load bearing equipment to the lower flange. This has lifting points each side and can be used independently or together for a balanced lift. Being of light weight construction can be fitted quickly.