Camlok

Camlok "HGC" Hand Grip Clamp - 250kg

Camlok HGC hand clamp for up to 250kg and 10mm thin plates, weighs only 1.4kg

Model: Camlok HGC / HGC-3034

Camlok Hand Grip Clamp's are suited to the individual transport of light and thin plates. It has a jaw capacity of up to 10mm, and can lift up to 250kg. The Unit itself weighs only 1.4kg.

Camlok TSH Screw-lock Pulling Clamp

Screw-locking beam clamp with alloy safety shackle for pulling up to 180 degrees. Range from 750kg to 5000kg.

Model: CTSH-4308

The Camlok series of screwcam clamps can be used on all structural steel plates and sections up to a surface hardness of 300 Brinell. They offer an easy way of attaching pulling equipment to steel structures and can be used for holding and for the correction of alignment problems. This range of clamps is designed for pulling in three planes. The design allows for simultaneous loading in two directions but not for the transportation of plate.

This series of clamps can be used in any combination or number of combinations required they are available in various sizes, lifting capacities and cap sizes.

Camlok "TSZ" Two-Way Pulling Screw Clamp

Manual screw locking beam clamp with two lifting points. Range 500kg to 7500kg.

Model: CTTP-4309

The Camlok series of screwcam clamps can be used on all structural steel plates and sections up to a surface hardness of 300 Brinell. They offer an easy way of attaching pulling equipment to steel structures and can be used for holding and for the correction of alignment problems. This range of clamps is designed for pulling in three planes. The design allows for simultaneous loading in two directions but not for the transportation of plate.

This series of clamps can be used in any combination or number of combinations required they are available in various sizes, lifting capacities and cap sizes.

Camlok 92 Series Vertical Plate Lifting Clamp

Best Seller! Camlok's standard vertical plate clamp with safety lock. Lifting capacity options from 500kg up to 3 tonnes.

Model: Camlok 92 / VPLC-336

Used on all hot rolled structural steel plates and sections upto a surface hardness of 300 Brinell/32 Rockwell C. Lifts plate from the horizontal to the vertical position and vice versa through 180. Fitted with hold-open and lock-closed device (not 92500).

Available to suit additional plate thicknesses

Camlok CZ Heavy Duty Plate Clamp

UK manufactured heavy-duty plate lifting clamp, designed to lift plate from the horizontal to vertical position and vice versa.

Model: Camlok CZ / VPLC-337

The Camlok CZ Series Vertical Plate Clamp differs from our CZ92 series in that the body of the clamp is a welded construction. The series has a lifting capacity range of 1 to 30 tons. The CZ series clamp can be used to lift plate from the horizontal to vertical position and vice versa. This clamp series is suitable for handling steel plate with a surface hardness of up to 300 Brinell. The standard clamp is fitted with a hook ring this can be replaced with a short length of chain and master link. The clamp can be supplied with alternative body shapes, Clamp jaws and pads are manufactured from high tensile steel and have heat treated serrated teeth.

Camlok CY Hinged Vertical Plate Clamp

UK manufactured vertical plate lifting clamp with hinge for angled lifts from horizontal to vertical and vice-versa. Capacity options from 1 to 3 tonne to suit up to 32mm steel plates.

Model: Camlok CY / HVPC-338

The CY Non-welded Hinged Universal Clamp is a variant of our successful CZ92 Series Clamp. The clamp has all the innovative design features of the CZ92 clamp and incorporates a hinged hook ring. This device enables the clamp to be used at any angle thus permitting awkward lifts previously considered hazardous. The standard clamp is fitted with a cam operated locking mechanism but this can be replaced (at no additional cost) by a chain pull locking mechanism. The CY range is fitted with hardened steel pads and jaws that incorporate tooth wear indicators. The clamp is designed to lift and handle plate with a surface hardness up to 300 Brinell. Contact our sales/technical department if plate to be lifted has a higher surface hardness. Other clamps in our range are available for this application.

Camlok CX Heavy Duty Hinged Plate Clamp

UK manufactured heavy-duty plate lifting clamps with hinge for angled lifts from horizontal to vertical or vice-versa. Capacity options from 1.5 to 10 tonnes, to suit plates up to 100mm thick.

Model: Camlok CX / VPLC-339

The Camlok Series CX range of clamps has been developed especially for the handling of plate at any angle, thus permitting the lifting and handling of awkward shaped plate and fabrications. Single plates can be lifted from the horizontal to the vertical position and vice versa. Vertically racked plates can be turned over due to the in-built lifting eye and link. Standard CX clamps are fitted with a cam operated closing mechanism that can, if preferred, be replaced with a chain pull open /close mechanism. Clamps are fitted with hardened serrated teeth, jaws and pads that are suitable for gripping steel plate up to a hardness of 300 Brinell.

Camlok HG High Grip Plate Clamp

500kg capacity high-grip vertical plate clamp, designed for lifting stainless steel or other hardened surface plates.

Model: Camlok HG / VPLC-340

Camlok LJR & LJL Non-Marking Plate Clamps

UK manufactured non-marking lifting clamps designed and suitable for use with a variety of different materials such as steel or timber. 500kg or 1500kg capacity.

Model: Camlok LJ / NPC-347

The LJ range of clamps is specifically designed to lift plates without marking or damaging the surface finish. The clamp is suitable for lifting various types of plate materials. eg. - steel, timber etc. The clamp is particularly suitable for lifting thin gauge steel plate, aluminium and stainless steel. The clamp is also suitable for steel with a surface hardness above 300 Brinell.

Options on Camlok Non marking clamp - 500kg/plate diameter 0 - 10mm, 1500kg/plate diameter 0 - 20mm.

Camlok "TAG" & "TWG" Wide Jaw Vertical Plate Clamps, Capacity Range from 75kg to 5000kg

Camlok Vertical Plate Lifting Clamp, Jaw Width Options upto 200mm

Model: CWJV-5393

Camlok "TSB" Gentle Grip Non-Marking Plate Clamps

Soft-grip non-marking lifting clamps to suit up to 65mm thick plates. Capacity options from 40kg to 1250kg.

Model: Camlok TSB / NPC-348

The TSB gentle grip clamp is designed to lift and handle various types of material such as steel, timber, plastics, laminates etc. without causing damage to the surface finish. The fixed pad and horizontally moving jaw are lined with hard wearing rubber. The lateral gripping load is transmitted to the moving jaw via a short length of chain routed between two chain pulleys. The clamp can be used to lift plates from the horizontal to vertical position and vice versa.

Options on Camlok grip non marking plate clamp - 350kg/plate diameter 0 - 65mm, 750kg/plate diameter 0 - 65mm, 1250kg/jaw opening 0 - 65mm.

Camlok PP Pile Pulling Clamp

UK manufactured clamps specifically designed to pull and remove driven piles or trench shields. Capacity options are 3 or 8 tonnes.

Model: Camlok PP / PPC-360

Camlok CP Pile Pitching Clamp

UK manufactured plate clamps designed specifically for lifting steel piles in to position. Supplied as standard with a 15 metre remote release rope. Capacity options from 2 to 5 tonnes.

Model: Camlok CP / PPC-361

The Camlok CP is designed specifically for pitching sheet steel piling, it is NOT designed to extract a driven pile. A rope is fitted for easy release from the ground.

Camlok "TJC" Twin Jaw Lifting Clamp - Range from 20kg to 300kg

Camlok Twin Jaw plate lifting clamp, specially designed for lifting steel plates.

Model: Camlok TJC / TJLC-3027

The Twin Jaw Range of Clamps from Camlok have been designed specifically for lifting steel plates. The main difference between these and the single jaw clamps is that the TJC has a unique twin moving jaw arrangement. This Design means the TJC can be used in applications where a larger jaw capacity is required, with a low minimum weight.

Camlok BTG Concrete Pipe Clamps

Set of 3 clamps designed specifically for the lifting of concrete pipe sections. Capacity options are 1.5 or 3 tonne.

Model: Camlok BTG / CPC-366

The Camlok BTG clamp is designed to vertically lift and position concrete manhole pipes. The clamps can be adjusted to different wall thicknesses using the adjusting pin and the holes inside the clamping arms. The BTG concrete pipe clamp is designed to vertically lift and position concrete manhole pipes. The clamps can be adjusted to different wall thicknesses using the adjusting pin and the holes inside the clamping arm. The clamps can be used in pairs with 2 leg chain slings or with 3 clamps and a 3 leg chain sling for larger diameters, providing they are attached in a way that the load is evenly distributed. Use of the BTG clamp enables the manhole trench size to be minimized and facilitates accurate pipe positioning.

Camlok "TPZ" Non-Marking Board Clamp - Range from 20kg to 1500kg

Camlok Non-Marking Board Clamp for Lifting Boards Between 5 & 150mm (various size options).

Model: Camlok TPZ / NBC-2643

This clamp facilitates the lifting and handling of all materials. Loads can be lifted from the vertical to the horizontal through 90 degrees for transportation. It is fitted with a handle to enable the operator to guide the load during transport. Fitted with large rubber pads to prevent damage. Ideal clamp for use in production facilities and on construction / building sites.

Camlok CG Girder Lifting Clamp

Camlok girder section lifting and turning clamps with jaw sizes from 0 - 50mm. 2000kg Capacity

Model: Camlok CG / GSLC-350

Camlok TTR Girder Section Lifting Clamp

Camlok H-beam or I-beam section clamps with jaw openings from 5 to 28mm. Lifting capacity options from 750kg up to 3 tonne.

Model: Camlok TTR / GSLC-351

The TTR Series of Clamps have been designed to lift and transport structural steel beams in the horizontal position i.e. with the flanges in the vertical position. The clamp is designed with the hook ring as near as to the centre of gravity of the beam as possible, thus resulting in a near horizontal lift. Long beams should be lifted using 2 clamps attached to opposite beam flanges. The clamp is fitted with a Camlok spring/cam operated safety lock.

Camlok THK Thin Sheet Horizontal Plate Clamps

UK manufactured plate lifting clamps, designed and sold to be used in pairs, for horizontally lifting single pieces of thin sheet or plate. Capacity options from 750kg up to 9 tonnes.

Model: Camlok THK / PLC-344

The Camlok THK Clamp has a jaw that pivots in the reverse direction to our normal horizontal clamps and is designed to lift and handle thin sheet plate that tend to sag when lifted. The reverse jaw feature ensures that the clamp grip increases the more the plate deflects under its own self weight. Clamps are used in pairs with a 2 legged chain sling (maximum included angle not to exceed 60º). Two pairs of clamps supported from a lifting beam must be used when handling long plates. Single plates only can be lifted.

Camlok CH & HH Horizontal Plate Clamps

Plate lifting clamps sold and designed to be used in pairs for horizontally lifting plates. Available with serrated or smooth jaws, in capacities from 1 to 20 tonnes.

Model: Camlok CH/HH / PLC-341

The CH/HH Series of plate clamps are sold in pairs. Optional plate thicknesses for wider plates. Used with a 2 leg sling upto 90º on all types of plate. The integral shackle is designed to accept, directly, the relevant sized chain sling hook.

Camlok "RH" Roller Toe Plate Clamp - Range from 1500kg to 5000kg

Camlok Roller Toe Horizontal Plate Lifting Clamps.

Model: Camlok RH / RTPC-2886

This range of horizontal plate clamps has been designed, to be used in pairs, for the horizontal transporting of individual and bundled plate. Whilst the basic design is the same, there are three different versions available.

RH Series - This range is fitted with a steel roller for reduced marking of the plates.
WH Series - The jaw is this range has hardened steel teeth for applications where the marking of plates is not an issue.
WHL Series - With a protective rubber lining on the jaw and the toe plate, this range totally eliminates any risk of marking.

Camlok PH Pipe Hooks

Pipe section hooks sold and designed to be used in pairs for horizontally lifting and transporting pipes or tubes from each end. Supplied with shackles, but chains are not included. Capacity options from 2 to 10 tonnes.

Model: Camlok PH / PH-362

Camlok PH Series Pipe Hooks are used in pairs to handle pipe / tubes etc.  Available with 2 legged chain slings and / or polyurethane coated Type A, 60 to 90 degrees Type B, 90 to 120 degrees. They are manufactured from special high tensile steel

SWL (safe working load) options available: 2 tonnes, 4 tonnes, 6 tonnes, 8 tonnes and 10 tonnes.

Camlok TTG Horizontal Girder Lifting Clamp

UK manufactured I-beam or H-beam flange clamp for horizontally lifting and stacking. Capacity options from 500kg up to 7.5 tonnes.

Model: Camlok TTG / GSLC-352

The TTG Girder Clamp is designed to lift and transport structural steel beams in the vertical position i.e with the flanges in the horizontal position. The clamp is fitted with a Camlok spring operated safety lock and is operated by pulling the locking handle upwards. Long beams should be lifted with two clamps attached on opposite beam flanges, the clamps supported from a lifting beam.

The TTG is ideal for lifting and transporting structural steel beams and girders. Long beams can be lifted using 2 clamps attached to opposite beam flanges. The clamp is fitted with a Camlok spring / cam operated safety lock.

Camlok TTT Girder Section Clamp

Horizontal I-beam or H-beam lifting clamps, designed and sold to be used in pairs for lifting beam sections in the vertical position with the flanges positioned horizontally. Capacity options from 500kg to 3 tonnes.

Model: Camlok TTT / GSC-354

The TTT Series Clamp is a variant of the TTG clamp but this clamp is designed to be used in pairs supported from a 2 legged chain sling. The bottom toe plate is split thus enabling the clamp to be attached to the end of the structural steel beam. The clamp is fitted with a spring operated safety lock. Particularly used for erecting structural beams on construction sites.

The Camlok series of TTT clamps can be used on girders up to a surface hardness of 300 Brinell. Girders can be lifted vertically from their ends so that steel beams can be transported with the flanges in a horizontal position.

Camlok ACH Adjustable Plate Lifting Clamps

UK manufactured plate clamps with adjustable jaw opening, for horizontal lifting of plates. Sold and designed to be used in pairs.

Model: Camlok ACH / PLC-343

The Camlok Adjustable Height Horizontal Plate Clamp is designed to lift and transport thick plate and plate bundles in the horizontal position. The clamps are used in pairs for short lengths of plate. For longer plate lengths 2 pairs of clamps suspended from a lifting beam are used. The height of the jaw pivot arm is easily adjusted via a spring locked rack and lock bar device. The clamping jaw is always positively brought into the correct position ensuring a safe and secure lift.

Camlok TCS Coil Lifting and Turning Hook

C-hook designed for safely lifting, turning and transporting of coils or reels. Capacity options from 500kg up to 3 tonnes.

Model: Camlok TCS / CTH-389

Camlok DC500 Drum Lifting Clamp

Can be used as a single clamp on sealed or empty drums or 2 clamps and chain sling on open drums. Clamps sold individually. 500kg lifting capacity per clamp.

Model: Camlok DC500 / DC-375

This range of clamps permit the safe handling of all types of flanged drums with or without lids. This can be used to lift sealed drums on their own, if an open drum is to be lifted without spilling the contents, two clamps can be used with either a two leg chain sling or a small lifting beam and two slings. (Chain sling not included)

Camlok drum clamps are available in the following size - 500kg.

Camlok DCV500 Crane Slung, Side Mounted Drum Grab

Camlok hook suspended rim grip drum grab for steel drums. 500kg lifting capacity.

Model: DCV500 / DG-385

Camlok DA & DAF Drum Clamps

350kg capacity low headroom steel drum lifting clamp for top/vertical lifting. DA is crane slung only. DAF is crane slung or forklift truck tine mountable.

Model: Camlok DA / DAF / DC-377

Camlok "SL" Shearleg / Tripods available from 500kg to 3000kg up to 3 metre high. (and specials)

Steel Shear-leg / Tripod with a variety of feet options to suit most working environments.

Model: Camlok SL / ST-400

Camlok CLB Container Bottom & Side Lifting Lugs

Bottom or side lifting eyes for shipping containers - 40 tonne (88,100 lbs) capacity per set of 4.

Model: Camlok CLB / CLL-388

Camlok CLT Container Top Lifting Lugs

Container eye fittings for lifting from the top blocks of a shipping container. 56 tonne capacity per set of 4.

Model: Camlok CLT / CLL-387

Camlok "TKG-VH" Manual Balance Crane Forks

Manually balancing crane slung lifting forks. Range from 1000 to 5000 kg (4 Options)

Model: Camlok TKG-VH / MBCF-397

Manual positioning of the fitting eye is required by the user to ensure the load is level and safe though there is no minimum SWL as there is with automatic balance crane forks. We also offer the same basic design an Auto Balance; in other words no manual intervention is required to level the load. A crane fork is a lifting device used to adapt an overhead crane into a system for safely handling pallets.

Camlok "TKG-VHS" Self Balance Crane Forks

Self weight-balancing crane forks. Capacity options from 1000 to 5000 kg.

Model: Camlok TKG-VHS / SBCF-396

A Crane fork effectively converts a hoist or overhead crane into a pallet moving tool, in some circumstances replacing a fork truck though also has many applications where a fork truck cannot be operated due to a lack of floor space. These crane forks are equipped with adjustable tines, height adjustable and an automatic balancing system. Crane forks with automatic balancing tend to point their tines upward when being transported. This prevents the load from unintentionally slipping off the tines.

Camlok "TTB" Big Bag Lifting Beam, Capacity 2000kg

Cruciform Spreader Beam for Lifting Big Bags, Bulk Bags, FIBC's (Flexible Intermediate Bulk Containers) or Large Totes

Model: Camlok TTB / BBSB-394

Excellent quality, made in Chester UK and available as 1 tonne or 2 tonne SWL in a choice of sizes to suit most applications. Contact us for other sizes and capacities as we will manufacture Big Bag lifting beams to your specification!

Camlok "TCK2 Coil Handler C-Hooks

UK manufactured coil handling hooks, built to meet your requirements.

Model: Camlok TCK / CHC-392

The Camlok TCK is designed for lifting and handling pipe sections, coils, rolls and rings etc. in the horizontal position. If collared pipes are to be lifted adjust the balance accordingly. Never try lift a load longer than the length and Mac working load specified.

Camlok TCK coil handler C-hook are available in the following standard capacities - 500kg, 1000kg, 2000kg, 3000kg, 5000kg, 7500kg, 10,000kg.Other and higher capacities are available on request.

Camlok "TZH" Single Tine Forklift Fork Tine Mounted Hook - Range From 1500kg to 5000kg

Adjustable single tine hook to convert a fork lift truck into a crane.

Model: Camlok TZH / STH-3033

Camlok TSA Lightweight Block Grab

Adjustable single arm block grab for lifting stone or concrete blocks and kerb stones etc. 250/500 kg. UK manufactured.

Model: Camlok TSA / SABG-370

This grab is fitted with a lock to secure the spring-loaded arm. The large handle makes it easy to carry by hand. It can be designed for any working load limit and with jaw width capacity to suit customer requirements. It is fitted with plastic pads for efficient grip and to prevent damage to the load. Designed for picking up kerbstones, blocks etc.

Camlok TBG & TST Scissor Block Grabs

Camlok scissor grab with rubber pads or teeth and with manual latching mechanism, for lifting blocks. Range from 200kg to 1000kg

Model: Camlok TBG / SBG-373

Camlok TPR Profile Steel Grab

Camlok lightweight I-profile steel grab. Lifting capacity options 500kg to 3 tonnes.

Model: Camlok TPR / PSG-374

This clamp is useful for various flange widths due to large jaw capacity. The clamping jaws hold the load firmly in place. Designed to transport girders, profile steel etc.

Models available: 500, 1500, 3000 kg

Camlok TRU Round Stock Grabs

Round section lifting clamps for tubes, pipes, rolls or similar up to 600mm dia. Capacity options from 100kg up to 3 tonnes. UK manufactured.

Model: Camlok TRU / RSG-368

Camlok "TKA" Tote Pan Grab

For lifting and transporting stackable steel tote pans. Capacity Range from 150kg to 200kg

Model: CTPG-5392

Camlok "MR" Multi Rail Clamp - Range from 5000kg to 8000kg

Multi Rail lifting grabs for handling from 3 to 8 rails (various size options). Recommended for use in pairs.

Model: Camlok MR / MRC-3030

Camlok Multi Rail Clamps are used for the fast bulk handling of a specific rail section. The section are locked into place with swivelling feet which locate under the rail-heads and top clamp body, that rotate, pressing a hard rubber lined beam onto the top of the rail head. The rubber lined contact beam prevents damage and marking to the rail heads. It is recommended that you use a pair of these clamps, at centres of 50 to 60% of rail length for rails of up to 20m long. For rails above 20m, three clamps at centre distance 65 to 75% of rail length must be used.

Camlok "MRC" Interchangeable Multi Rail Grab - Range from 5000kg to 8000kg

Camlok MRC series multi rail clamp for the handling of 3 to 8 rails.

Model: Camlok MRC / MRG-3031

An additional feature of the MRC is that it is possible to fit the grab with an automatic opening/closing device that automatically engages the rail when lifted from its resting position on top of the rails.