Tractel TOPAL TC Automatic Load Positioner for Single Rope - Range from 2000kg to 5000kg
Tractel TOPAL TC Automatic Load Positioner for Single Rope - Range from 2000kg to 5000kg
Automatic load positioner for single wire rope
Model:
TOPAL TC
Quick Ref:
TTT-3318
More from:
Slide the beam slantwise in the cone-shaped manhole, then fix horizontally. As the lift is applied, the polyurethane coated pads will engage and grip the inner wall diameter reduction, holding at about 700 mm. So as to free the beam, release the tension on the sling and take the beam out of the manhole, gripping it by its ends.
When lifting, the rope sling locks itself around the ring thanks to a round turn. Should the load be unbalanced too much (more than 70 % effort on 1 leg and less than 30 % on the other), put down the load again and slacken the sling so as to free the tension around the ring. Resume the operation until the desired position be obtained. Then the handling of the load can be performed.
Instructions For Use
Thread the rope into the load positioner.
In the free position, with the sling slackened: the rope turns around the ring (4) of the load positioner enabling the positioner to be moved in order to be placed in position above the presumed centre of gravity of the part to be lifted.
Hang the load positioner + sling to the lifting appliance.
Fasten the legs of the sling to the part to be lifted.
Look for the centre of gravity: move the load positioner to set it in the position above the presumed centre of gravity above the part to be lifted.
Perform the lifting operation whereby the rope sling locks around the ring of the load positioner by means of a full turn of the sling.
If there is too much unbalance, put the part back down and slacken the sling to free the tension around the ring of the load positioner.
Resume from operation n° 5 until the position above the centre of gravity of the part is determined.
Once this position has been found, the part can be moved.
Specifications
Part No:
Capacity (kg)
Rope Ø (mm)
TC2
2000kg
11mm
TC3
3000kg
13mm
TC5
5000kg
18mm
Make sure the relations between the WLL and the angle between the legs of the slings are adhered to (see table below)
Reference
Wire rope in mm
WLL (kg) @ 45°
WLL (kg) @ 90°
WLL (kg) @ 120°
TC2-11
11
2000
1400
7000
TC3-13,2
13
3000
2100
1500
TC5-18
18
5000
3500
2500
One les of the sling should not baar more tahn 70% of the load.
The fastening points of the legs of the slings on the load must neaver be situated inderneath the load positioner.
Use a rope diameter equal to or greater taht the one specified in the above table
For any load positioning requiring more tahn 2 fastening points, use several load positioners
Please consult us for any use in a specific aggressive atmospher
If you wish to receive a quote for this product, please use the tab, this form is for general enquiries regarding this product only.
Regarding: Tractel TOPAL TC Automatic Load Positioner for Single Rope - Range from 2000kg to 5000kg
Did you know?
You can also request a quote through the pricing tab!
You can easily add more than one item to the Quote Request. This is highly recommended as we will be able to suit your needs much more efficiently.
Share this page!
Slide the beam slantwise in the cone-shaped manhole, then fix horizontally. As the lift is applied, the polyurethane coated pads will engage and grip the inner wall diameter reduction, holding at about 700 mm. So as to free the beam, release the tension on the sling and take the beam out of the manhole, gripping it by its ends.
When lifting, the rope sling locks itself around the ring thanks to a round turn. Should the load be unbalanced too much (more than 70 % effort on 1 leg and less than 30 % on the other), put down the load again and slacken the sling so as to free the tension around the ring. Resume the operation until the desired position be obtained. Then the handling of the load can be performed.
Instructions For Use
Thread the rope into the load positioner.
In the free position, with the sling slackened: the rope turns around the ring (4) of the load positioner enabling the positioner to be moved in order to be placed in position above the presumed centre of gravity of the part to be lifted.
Hang the load positioner + sling to the lifting appliance.
Fasten the legs of the sling to the part to be lifted.
Look for the centre of gravity: move the load positioner to set it in the position above the presumed centre of gravity above the part to be lifted.
Perform the lifting operation whereby the rope sling locks around the ring of the load positioner by means of a full turn of the sling.
If there is too much unbalance, put the part back down and slacken the sling to free the tension around the ring of the load positioner.
Resume from operation n° 5 until the position above the centre of gravity of the part is determined.
Once this position has been found, the part can be moved.
Specifications
Part No:
Capacity (kg)
Rope Ø (mm)
TC2
2000kg
11mm
TC3
3000kg
13mm
TC5
5000kg
18mm
Make sure the relations between the WLL and the angle between the legs of the slings are adhered to (see table below)
Reference
Wire rope in mm
WLL (kg) @ 45°
WLL (kg) @ 90°
WLL (kg) @ 120°
TC2-11
11
2000
1400
7000
TC3-13,2
13
3000
2100
1500
TC5-18
18
5000
3500
2500
One les of the sling should not baar more tahn 70% of the load.
The fastening points of the legs of the slings on the load must neaver be situated inderneath the load positioner.
Use a rope diameter equal to or greater taht the one specified in the above table
For any load positioning requiring more tahn 2 fastening points, use several load positioners
Please consult us for any use in a specific aggressive atmospher
