SWL (safe working load) options available: 2 tonnes, 4 tonnes, 6 tonnes, 8 tonnes and 10 tonnes.
The Camlok CP is designed specifically for pitching sheet steel piling, it is NOT designed to extract a driven pile. A rope is fitted for easy release from the ground.
The Camlok BTG clamp is designed to vertically lift and position concrete manhole pipes. The clamps can be adjusted to different wall thicknesses using the adjusting pin and the holes inside the clamping arms. The BTG concrete pipe clamp is designed to vertically lift and position concrete manhole pipes. The clamps can be adjusted to different wall thicknesses using the adjusting pin and the holes inside the clamping arm. The clamps can be used in pairs with 2 leg chain slings or with 3 clamps and a 3 leg chain sling for larger diameters, providing they are attached in a way that the load is evenly distributed. Use of the BTG clamp enables the manhole trench size to be minimized and facilitates accurate pipe positioning.
Camlok Hand Grip Clamp's are suited to the individual transport of light and thin plates. It has a jaw capacity of up to 10mm, and can lift up to 250kg. The Unit itself weighs only 1.4kg.
The Camlok Series CX range of clamps has been developed especially for the handling of plate at any angle, thus permitting the lifting and handling of awkward shaped plate and fabrications. Single plates can be lifted from the horizontal to the vertical position and vice versa. Vertically racked plates can be turned over due to the in-built lifting eye and link. Standard CX clamps are fitted with a cam operated closing mechanism that can, if preferred, be replaced with a chain pull open /close mechanism. Clamps are fitted with hardened serrated teeth, jaws and pads that are suitable for gripping steel plate up to a hardness of 300 Brinell.
The TSB gentle grip clamp is designed to lift and handle various types of material such as steel, timber, plastics, laminates etc. without causing damage to the surface finish. The fixed pad and horizontally moving jaw are lined with hard wearing rubber. The lateral gripping load is transmitted to the moving jaw via a short length of chain routed between two chain pulleys. The clamp can be used to lift plates from the horizontal to vertical position and vice versa.
Options on Camlok grip non marking plate clamp - 350kg/plate diameter 0 - 65mm, 750kg/plate diameter 0 - 65mm, 1250kg/jaw opening 0 - 65mm.
Used on all hot rolled structural steel plates and sections upto a surface hardness of 300 Brinell/32 Rockwell C. Lifts plate from the horizontal to the vertical position and vice versa through 180. Fitted with hold-open and lock-closed device (not 92500).
Available to suit additional plate thicknesses
The TTT Series Clamp is a variant of the TTG clamp but this clamp is designed to be used in pairs supported from a 2 legged chain sling. The bottom toe plate is split thus enabling the clamp to be attached to the end of the structural steel beam. The clamp is fitted with a spring operated safety lock. Particularly used for erecting structural beams on construction sites.
The Camlok series of TTT clamps can be used on girders up to a surface hardness of 300 Brinell. Girders can be lifted vertically from their ends so that steel beams can be transported with the flanges in a horizontal position.
The TTG Girder Clamp is designed to lift and transport structural steel beams in the vertical position i.e with the flanges in the horizontal position. The clamp is fitted with a Camlok spring operated safety lock and is operated by pulling the locking handle upwards. Long beams should be lifted with two clamps attached on opposite beam flanges, the clamps supported from a lifting beam.
The TTG is ideal for lifting and transporting structural steel beams and girders. Long beams can be lifted using 2 clamps attached to opposite beam flanges. The clamp is fitted with a Camlok spring / cam operated safety lock.
This range of horizontal plate clamps has been designed, to be used in pairs, for the horizontal transporting of individual and bundled plate. Whilst the basic design is the same, there are three different versions available.
RH Series - This range is fitted with a steel roller for reduced marking of the plates.WH Series - The jaw is this range has hardened steel teeth for applications where the marking of plates is not an issue.WHL Series - With a protective rubber lining on the jaw and the toe plate, this range totally eliminates any risk of marking.
The Camlok Adjustable Height Horizontal Plate Clamp is designed to lift and transport thick plate and plate bundles in the horizontal position. The clamps are used in pairs for short lengths of plate. For longer plate lengths 2 pairs of clamps suspended from a lifting beam are used. The height of the jaw pivot arm is easily adjusted via a spring locked rack and lock bar device. The clamping jaw is always positively brought into the correct position ensuring a safe and secure lift.
This range of clamps permit the safe handling of all types of flanged drums with or without lids. This can be used to lift sealed drums on their own, if an open drum is to be lifted without spilling the contents, two clamps can be used with either a two leg chain sling or a small lifting beam and two slings. (Chain sling not included)
Camlok drum clamps are available in the following size - 500kg.
This clamp is useful for various flange widths due to large jaw capacity. The clamping jaws hold the load firmly in place. Designed to transport girders, profile steel etc.
Models available: 500, 1500, 3000 kg
This grab is fitted with a lock to secure the spring-loaded arm. The large handle makes it easy to carry by hand. It can be designed for any working load limit and with jaw width capacity to suit customer requirements. It is fitted with plastic pads for efficient grip and to prevent damage to the load. Designed for picking up kerbstones, blocks etc.
LiftingSafety uses cookies to improve your user experience, To accept this, please click the 'accept' button below.